In some case, a fuse is very important for your electronic circuit and device. With this very cheap component, you will protect your expensive circuit/device from damage (or explosion.. ). Here the little explanation about fuse.

In electronics and electrical engineering a fuse (from the Latin “fusus” meaning to melt) is a type of sacrificial overcurrent protection device. Its essential component is a metal wire or strip that melts when too much current flows, which interrupts the circuit in which it is connected. Short circuit, overload or device failure is often the reason for excessive current.

A fuse interrupts excessive current (blows) so that further damage by overheating or fire is prevented. Wiring regulations often define a maximum fuse current rating for particular circuits. Overcurrent protection devices are essential in electrical systems to limit threats to human life and property damage. Fuses are selected to allow passage of normal current and of excessive current only for short periods.

A fuse was patented by Thomas Edison in 1890 as part of his successful electric distribution system.

This is the explanation about “Voltage”

Voltage is commonly used as a short name for electrical potential difference. Its corresponding SI unit is the volt (not italicized). Electric potential is a hypothetically measurable physical dimension, and is denoted by the algebraic variable V (italicized )

The voltage between two (electron) positions “A” and “B”, inside a solid electrical conductor (or inside two electrically-connected, solid electrical conductors), is denoted by (V_A − V_B). This voltage is the electrical driving force that drives a conventional electric current in the direction A to B. Voltage can be directly measured by an “ideal voltmeter”. Well-constructed, correctly used, real voltmeters approximate very well to ideal voltmeters. For non-scientists, an analogy involving the flow of water is sometimes helpful in understanding the concept of voltage (see below).

Precise modern and historic definitions of voltage exist, but (due to the development of the electron theory of metal conduction in the period 1897 to 1933, and to developments in theoretical surface science from about 1910 to about 1950, particularly the theory of local work function) some older definitions are not now regarded as strictly correct. This is because they neglect the existence of “chemical” effects and surface effects. A particular lesson from surface science is that, to get consistency and universality, formal definitions must relate to positions or (better) electron states inside conductors.

The electronic component, Light Dependent Resistor (LDR) or often called photoresistor or cadmium sulfide (CdS) cell is a resistor whose resistance decreases with increasing incident light intensity. It can also be referenced as a photoconductor.

A Light Dependent Resistor (LDR) is made of a high resistance semiconductor. If light falling on the device is of high enough frequency, photons absorbed by the semiconductor give bound electrons enough energy to jump into the conduction band. The resulting free electron (and its hole partner) conduct electricity, thereby lowering resistance.

A LDR device can be either intrinsic or extrinsic. An intrinsic semiconductor has its own charge carriers and is not an efficient semiconductor, e.g. silicon. In intrinsic devices the only available electrons are in the valence band, and hence the photon must have enough energy to excite the electron across the entire bandgap. Extrinsic devices have impurities, also called dopants, added whose ground state energy is closer to the conduction band; since the electrons do not have as far to jump, lower energy photons (i.e., longer wavelengths and lower frequencies) are sufficient to trigger the device. If a sample of silicon has some of its atoms replaced by phosphorus atoms (impurities), there will be extra electrons available for conduction. This is an example of an extrinsic semiconductor.

This article will teach you how to check measure a diode. This is a basic knowledge for students and electronic hobbysts. If your project is failed or your electronic device is broken, then you need to check the components. And before you check the components, you need to learn how to check and measure the components. Here is the explanation about how to check the diode:

________________________

Being able to determine the polarity (cathode versus anode) and basic functionality of a diode is a very important skill for the electronics hobbyist or technician to have. Since we know that a diode is essentially nothing more than a one-way valve for electricity, it makes sense we should be able to verify its one-way nature using a DC (battery-powered) ohmmeter as in Figure below. Connected one way across the diode, the meter should show a very low resistance at (a). Connected the other way across the diode, it should show a very high resistance at (b) (“OL” on some digital meter models).

Here the simple LED flasher circuit that you can use for your simple project.

schematic diagram:

component part list: